or can't find something you are looking for?
Call and speak with a representative M-F 2pm to 7pm Arizona Time 520-429-6493
aeroXcraft Quad-670 Air Frame Kit
- aeroXcraft Quad-670 Air Frame Kit
New! aeroXcraft Quad-670 Multicopter Kit Designed primarily for use with the DJI Wookong M, the Aeroxcraft Quad-670 has a dedicated place for all the major WKM components. Under the dome the controller plate has places for the Main Controller, IMU, PMU and for your radio RX. On the rear of the frame is a place to mount your DJI GPS/Compass unit, with the ability to fine tune it's direction. Under the Quad, on the rear battery plate there is a mounting bracket for the DJI LED unit, which solves the problem of seeing the unit whilst in flight.
Not everyone wants to use the DJI WKM, luckily the Quad-670 will work with any other suitable multirotor controller. There is a custom mounting plate available for the Aeroquad Sheild 2.0. Contact us if you require this.
This quad was designed to compliment the Aeroxcraft GoPro Gimbal. The GoPro Gimbal sits right out front allowing your GoPro HD to take great footage without getting the Quad-670 in shot. The flight batteries are use to counter balance the weight of the camera allowing you to make sure the center of gravity is in the correct place.
The motor mounts will take motors up to 35mm in diameter, including Axi 2814/22 and Park480 1020kv.
Specifications: - 670mm span (motor to motor) - G10 frame and aluminium booms. - All hardware included. - Bare frame weight, inc dome cover and Landing Gear: 720g
Includes: - All hardware and fittings. - A2 Stainless screws and nuts. - CNC G10 and Aluminium frame parts - Comprehensive Assembly instructions.
Example of a typical setup: DJI Wookong M Avroto 770Kv Motors Graupner Elektro Props - 11x5 2x ZIPPY Flightmax 4000mAh 3S1P 20C lipo batteries GoPro Gimbal All up weight including batteries and camera 2700g. Flight time 12 minutes.
Notes: - Full spares backup. - Assembly required. Full instructions included. - Gimbal not included - DOES NOT INCLUDE MOTORS, WIRING, ELECTRONICS OR RADIO - Designed and Manufactured in the UK by AeroXcraft Ltd.
DroidWorx CX Quad-Copter Air Frame Kit
- DroidWorx CX Quad-Copter Air Frame Kit
New! DroidWorx CX Quad-Copter Air Frame Kit.
The CX-4 airframe comes complete for self-assembly and is suited for fitting most current electronics like MikroKopter UAV, Hoverfly (Pro and Sport), DJI Wookong, Arducopter, Open Pilot, UAVP-NG and more!
As a compact craft (600mm diameter) the Droidworx CX-4 is designed for multiple tasks from extreme sports filming with POV cameras like GoPro HD and Contour or thermal imaging cameras (Tau/FLIR) for applications in the services sector such as surveillance, inspection of infrastructure/property (power lines, bridges, buildings, crops), fire spotting and SAR operations. Great care and resources were invested in the development of this craft, which is particularly valued for its potential to be of assistance in (natural) disaster zones and hazardous situations – as well as in planning and maintenance tasks.
New Scorpion Motor Version of the 330X-S With More Powerful Scorpion Motors and 10 amp Speed Controllers The 330X-S was designed based on UAV, which emphasizes the advantages of: 1. Flight Efficiency: Standard Battery (2S2000mAh) time of flight for more than 12min, with a high-capacity battery, the flight time will be more than 20 min or more (available spreadsheet calculation) 2. Excellent wind resistance: the efficiency and load of propeller are perfectly optimized, so the wind resistance will be better than general electric aircraft 3. High stability: contains GU344 (three-axis stabilizing system) for the beginner or the FPV flying, it is a very stable Vehicle 4. Additional payload capabilities: payload up to 700g (including battery), can freely install cameras and video recorder, and other general system 5. System Extensibility: can be used with GPS positioning system and navigation system on 330X-S without any change 6. Operation mode and flight characteristics with the same helicopter, but no complex transmission 7. Collapsible body design, greatly reduce the damage rate, Which can be repaired easily without adjustment.
Motor Spacing: 330mm (Shaft to Shaft) Propeller Size: 8 in. Motor: (4) Scorpion KV1100 brushless motors ESC: (4) 10A ESC Weight: 400g (without Battery) Maximum Flying Weight: 1100g (Including Payload and Battery) Battery: 7.4V to 11.1V (2S to 3S LiPo) Flying duration: 7~20 minutes (It may vary according to battery capacity and Payload)
PLEASE NOTE NOT INCLUDING TRANSMITTER RX OR BATTERIES
RC CARBON GOPRO CF CAMERA MOUNT w/Savox Servo Upgrade
- RC CARBON GOPRO CF CAMERA MOUNT w/Savox Servo Upgrade
RC Carbon Carbon Fiber Camera Mount for UAV Multicopters with Savox Servo Upgrade Specially Designed to hold the GoPro Camera System Comes Equipped with two Turnigy TGY930 Servos Each axis is Hung on Ball Bearings Working Angles: Ailerons (+ - 30 Degrees) Elevator (-90 Degrees +10 Degrees) Camera Mount Weight: 210gr Gyros not included.
RC CARBON SMALL SPY QUAD COMBO SET WITH GOPRO CAMERA MOUNT
- RC CARBON SMALL SPY QUAD COMBO SET WITH GOPRO CAMERA MOUNT
Carbon Fiber / Aluminum foldable Frame Set for 500mm size Quad (can be used for Gaui 330XS as upgrade Kit)
Set includes: • Carbon Fiber Landing Gears with high clearance for Small Spy series copters are compatible with GoPro camera mount • CF Main Frame • Aluminium motor arms • CF Motor Mounts for motors with case diameter 28mm • CF Landing gear/skids • Two battery sliders
GoPro Camera Mount
Frame equipped with FPV camera holder. Can be installed with 10"-12'' inches props.
Set weight: 355 gm
RC CARBON Y-6 CF 920MM AIR FRAME SET
- RC CARBON Y-6 CF 920MM AIR FRAME SET
New! RC CARBON Carbon Fiber Y-6 920mm Foldable Air Frame
This co-axial Y-6 air frame is part of our new professional products line , which was designed and tested within last three months. It`s made from extra strong carbon fiber plates and tubes, which we produce in our workshop using our own technology and equipment. It`s build to provide very smooth and stable flight with up 2kg payloads.
This frame is foldable (as all our frames) it`s very comfortable for travel . Just release 7pcs of wing nuts to fold front motor arms and landing gears to put your copter into it's storage position. The protection cage will keep the copter`s electronic equipment safe. Also the camera mount adaptor plate is specially designed to reduce vibration on camera . It`s compatible with all Rc Carbon Camera mounts and Photo Higher AV130 or AV200.
The holes to mount the MikroKopter electronics are already Drilled in the centerplate, as the ones necessary for the distribution board with the speed controllers. If necessary adaptor plates for HoverFly, or DJI WooKong are also available for this frame.
This kit includes a large foldable landing gear (300mm of clearance). The Y-6 frame is delivered partially assembled, so building is faster and easier. Diameter of the frame is 920mm. Weight of the frame with landing gear, protection cage and camera mount adaptor plate is 840grams.
Vulcan UAV SkyHook 900mm Hexa STD-LG
- Vulcan UAV SkyHook 900mm Hexa STD-LG
New VulcanUAV SkyHook 900mm Hexa MultiFrame Kit Standard LG(178MM)